Operations & production
Process & yield optimization
Models recommend or automatically adjust process setpoints to keep quality on target while improving yield, throughput and energy use.
Use case · Engineering & R&D
Machine learning chooses which experiments, formulations or process recipes to run next, often on automated lab equipment, so R&D teams reach a working recipe in fewer rounds.
1 quantified outcome across 1 deployment
Each dot is one reported improvement, as published by its source; the black tick is the median. Figures come from different baselines and methods, so read them as the range of reported results, not a forecast.
Machine learning directs the design-build-test-analyse-learn cycle so thousands of microbial strain experiments run at once on automated lines.
| Manufacturer | Evidence | Outcome as reported |
|---|---|---|
| Zymergen | Independently assessed | resulting in a doubling of its innovation rate |
ML-guided experimentation uses machine learning, commonly Bayesian optimization and active learning, to decide which experiments to run next in product and process development. Instead of testing a fixed grid of formulations or process settings, the model learns from each result, estimates where better outcomes are likely and where it is most uncertain, and proposes the next batch of experiments that is expected to teach the most or improve the target the fastest. In some labs the proposals run directly on automated equipment such as liquid handlers, reactors, coating lines or test rigs, creating a closed loop of design, run, measure and update.
It matters because developing a new formulation, material, battery chemistry, semiconductor recipe or process window often means searching a space with many interacting variables, where each experiment is slow or expensive. Traditional one-factor-at-a-time work and even classical design of experiments can need many rounds to find a good region. Choosing experiments more intelligently can cut the number of runs needed, and keeping every result in a structured model preserves what was learned for the next project.
Scientists and engineers set the targets, such as strength, purity, yield, cost or cycle time, the constraints that must be met, and the variables the experiments can change, including ingredient ranges, temperatures, times and process settings.
Past experiments, lab notebooks, literature values and a small initial design give the model a starting picture. Results must be recorded in a structured form with the conditions that produced them.
The model estimates outcomes and uncertainty across the space and proposes a batch of experiments that balances exploring unknown regions with refining promising ones, while respecting safety and feasibility limits.
Experiments are run by technicians or on automated lab equipment, and measurements flow back into the data set, ideally directly from instruments and the lab information system rather than by hand.
The model updates after each batch, and the team decides when results are good enough to move to pilot or production scale, where the same approach can tune the process window on larger equipment.
Choosing each batch based on what has been learned so far avoids running experiments in regions that are already understood or clearly poor, which shortens development cycles.
Models capture interactions between ingredients and process settings that one-factor-at-a-time testing misses, which helps find combinations people might not try.
Automated equipment can run around the clock when the next experiments are chosen by software, instead of waiting for a scientist to analyze results and plan the next round.
Every experiment is stored with its conditions and outcomes in a structured model, so the next product or project starts from accumulated knowledge rather than scattered notebooks.
Classical design of experiments plans a set of runs up front and analyzes them together. ML-guided experimentation is sequential: it updates its model after each batch and chooses the next experiments based on what it has learned. The two are often combined, with a classical design used to seed the model.
No. Many teams start with technicians running the experiments the model proposes. Automation adds speed and consistency once the loop is working, but the main gains come from choosing better experiments and recording results in structured form.
Yes. The same sequential approach can tune process settings on pilot lines or production equipment, where each trial run is expensive. In production, trials are usually constrained more tightly to protect quality and safety, and the work overlaps with process optimization.
Operations & production
Models recommend or automatically adjust process setpoints to keep quality on target while improving yield, throughput and energy use.
Quality
Predict product quality from live process data so problems are caught before parts are measured, tested or shipped.
Engineering & R&D
AI generates design options from requirements and replaces slow simulations with fast surrogate models so engineers explore more designs.
Engineering & R&D
Language models and machine learning mine product reviews, social posts, support tickets and sales data to show what customers want, so product teams pick stronger concepts and reach launch sooner.
Put AI to work
Genvo, our implementation partner, works with manufacturers to pick the right first project, connect the systems you already run and put AI agents and tools into daily use, with people approving what goes out.
Assessments and consultations are provided by Genvo. How our partnership works.